Adding a consecrate graphics card to your PC can dramatically transform both its gambling and substance creation capabilities .
In this guide we take you through open up your PC , plugging in a new nontextual matter card , and getting it ready for divine service . If you are supersede a old card , please train the FAQ for pourboire on removing the older fashion model .
One of the most popular PC upgrades is a unexampled graphics lineup . You might be move from integrated graphics – the on - chip graphics provided by yourCPU – or upgrading from an older , slower and less capable graphics wag .
If you are read this templet and have yet to determine upon and purchase a special nontextual matter wag , then please make certain the model you are buying will fit in the PC case you have ( mark off producer specs page of your case and graphics card ) . Another important consideration is making indisputable you have sufficient PSU office and spare office connectors for the graphic wag you have pick out .
Hardware used
The short version
Step 1.
Unplug and open up
disconnect the power cable from your microcomputer . You could give it on your desk , or unplug all the cable and take it to a sporting workplace surface with proficient lighting and access , like we did . Next , take off the side panel and remove PCI bracket covers on the back of your case to match the graphics card you have bought . Most New art card bind to two expansion bracket .
Step 2.
Unbox, line up and slot in the graphics card
If your PCIe slot is vacant , you will now unbox and divulge your graphics scorecard , hit any plastic cover – ours had a bumper over the Au striking which insert into your motherboard one-armed bandit . Now position the graphics card atomic number 79 contact over the expansion slot with the bracket connecter above the vacant bracket(s ) too . You will be seating the nontextual matter card and push down on its spine with even and positive pressure . You should experience the graphics card skid into the expansion slot and reach its stable fit position . Now insert and constrain the square bracket screws , secure the card in billet .
Step 3.
Connect cabling and make some checks
plug away any required big businessman cable(s ) from your PSU into your graphics card . Some graphics cards may not need any top executive connectors , draw any required power from the PCI slot , but at the other end of the spectrum some very potent graphics bill of fare need up to three power connection . Before closing up your case , have a ready check that your cabling is tidy , and the graphics card fans are n’t hindered by any cabling , so they spin freely .
Step 4.
Connect your monitor to one of your new graphics card display outputs
After shut your fount , you might be eager to stop up everything back in and check out your PC ’s new graphics firepower . Please give limited attention to plugging your monitor into a graphics card port rather than one of your motherboard supervise outputs . In our example , we had been using merged graphics via HDMI from the motherboard rear I / O plate . For the nontextual matter card , we chose to connect to the monitor via a DisplayPort cable television service to benefit from Adaptive Sync ( FreeSync / G - Sync).With your computer hardware now instal , you might have to snap up a new graphics card driver for Windows ( if you switched brand or strike from an iGPU ) to benefit from the ironware speedup .
FAQs
AMD graphics driver can be foundhere , Nvidia artwork bill machine driver arehere , and Intel art drivers arehere .
Firstly , uninstall the nontextual matter card driver if you are switch brand . Then turn off and disconnect your personal computer before open up it up . Next , you may disconnect any auxiliary power joining your existing card enjoyment , and unmake the rearward expansion bracket screw(s ) and pose them aside . Your graphics circuit board slot might have a servant chemical mechanism , so as you lift out the old card , you will have to accomplish under the card and crusade the door latch down to unhook your honest-to-goodness graphics circuit board . If you have done all this , you could accompany our guide .
First , verify your proctor is power up and correct stimulus selected using the monitor ’s built - in computer menu system of rules ( often called the OSD ) . If that does n’t assist , turn off the personal computer and disconnect it before opening up the side panel and check the world power connector(s ) fit , the graphics card seating is firm , and you have plugged the monitor into the new graphic card and not , for instance , a motherboard furnish video output . If everything agree out , please debate your power supply might be insufficient for the upgrade you have chosen .
